Kia Rio
+ 1.1. Short acquaintance to the car
+ 2. Engines A3E, А5D
+ 3. Greasing system
+ 4. Cooling system
+ 5. Fuel system
+ 6. Ignition system
+ 7. Coupling
+ 8. A transmission
+ 9. Axes and power shafts
+ 10. A suspension bracket
+ 11. Wheels and tyres
- 12. A steering
12.1. Specifications
12.2. A steering without the hydraulic amplifier
12.3. Check of the helmsman management without the hydraulic amplifier
12.4. A steering column without the hydraulic amplifier
12.5. A steering with the hydraulic amplifier
12.6. Check of pressure of a liquid in hydraulic system
12.7. Check of effort of turn of a steering wheel
12.8. Check of level of a liquid
12.9. Prorolling of hydraulic system of the amplifier of a steering
12.10. A belt of a drive of the pump of the amplifier of a steering
12.11. Steering transfer with the steering amplifier
12.12. The pump of the amplifier of a steering
+ 13. Brake system
+ 14. A body
+ 15. Air central air
+ 16. The electric equipment
|
The pump of the amplifier of a steering
1 – a belt of a drive of the pump;
2 – an electric socket;
3 – a returnable hose;
4 – a pressure head hose;
5 – a hollow bolt; |
6 – a bolt;
7 – an adjusting bolt;
8 – an adjusting arm;
9 – шарнирный a bolt;
10 – a bolt. |
The pump of the amplifier of a steering
1 – a soaking up pipe;
2 – a sealing ring of round section;
3 – the pressure gauge;
4 – a sealing ring of round section;
5 – a stopper;
6 – a sealing ring of round section;
7 – the regulating valve;
8 – a spring;
9 – an adjusting arm;
10 – the pump case (a back part); |
11 – a sealing ring of round section;
12 – статорное a ring;
13 – blades;
14 – a rotor;
15 – a lateral plate;
16 – a sealing ring of round section;
17 – a sealing ring of round section;
18 – a pin;
19 – the pump case (a forward part). |
Removal
PERFORMANCE ORDER |
|
1. Disconnect an electric socket from the pressure gauge. |
|
2. Disconnect soaking up hose. |
|
3. Disconnect a pressure head hose. |
|
4. Loosen the an assembly bolt. Loosen the a tension also remove a belt of a drive of the pump. |
5. Turn out an assembly bolt. |
6. Remove the pump of the amplifier of a steering. |
|
Check
The prevention If necessary replace the pump of the amplifier of a steering in gathering.
PERFORMANCE ORDER |
|
1. Check up forward and back parts of the case of the pump on absence of cracks, damages and non-uniform deterioration of a rotor. |
2. Check up a surface статорного the rings, interfaced to blades on absence of non-uniform deterioration. |
3. Check up surfaces of a lateral plate and the cases of the pump interfaced to mobile details on absence of non-uniform deterioration. |
|
4. Check up a backlash between a rotor and blades. |
5. Check up regulating valve on absence of cracks, damages and non-uniform deterioration of a rotor. |
|
6. Check up a condition of a spring of the regulating valve. |
|
Remarks on assemblage
PERFORMANCE ORDER |
|
1. Establish a rotor an identification label upwards. |
|
2. Establish статорное a ring an identification label downwards. |
|
3. Establish ten blades flat parts in rotor grooves. |
|
Installation
PERFORMANCE ORDER |
|
1. Establish the pump of the amplifier of a steering and fix an assembly bolt. |
2. Establish a belt of a drive of the pump. |
3. Connect to the pump a pressure head hose and fix its bolt. The inhaling moment: 44–54 Nm |
4. Tighten a counternut and a bolt. The inhaling moment: 37–52Nm |
|
5. Connect to the pump a returnable hose. |
The prevention Check up that the white label on a returnable hose is combined with a white label on a pipe.
|
6. Rotating an adjusting bolt adjust tension of a belt of a drive of the pump. |
7. Connect an electric socket to the pressure gauge. |
|
|
|