KIA RIO

Since 2000 of release

Repair and car operation



Kia Rio
+ 1.1. Short acquaintance to the car
+ 2. Engines A3E, А5D
+ 3. Greasing system
+ 4. Cooling system
+ 5. Fuel system
+ 6. Ignition system
+ 7. Coupling
+ 8. A transmission
+ 9. Axes and power shafts
+ 10. A suspension bracket
+ 11. Wheels and tyres
+ 12. A steering
- 13. Brake system
   13.1. Specifications
   13.2. Check of the vacuum amplifier of brakes with use of devices
   13.3. The unilateral vacuum valve
   13.4. The vacuum amplifier of brakes
   13.5. Prorolling of hydraulic system of a drive of brakes
   13.6. Check of brake tubes
   13.7. Check and replacement of brake hoses
   + 13.8. A brake pedal
   13.9. Replacement of lobbies brake колодок
   13.10. Replacement brake колодок on back drum-type brakes
   13.11. Repair of a support of a forward brake
   13.12. Repair of the working brake cylinder
   13.13. The main brake cylinder
   13.14. The pressure terminator
   13.15. A lay brake
   13.16. The block of management ABS
   13.17. The block of hydraulic management (HCU)
   13.18. The forward gauge of frequency of rotation of a wheel
   13.19. The back gauge of frequency of rotation of a wheel
   + 13.20. A gear rotor of the gauge of frequency of rotation of a wheel
   13.21. The basic survey
   13.22. Check of functionality
+ 14. A body
+ 15. Air central air
+ 16. The electric equipment


cheap cvv




13.10. Replacement brake колодок on back drum-type brakes
THE GENERAL DATA

Brake колодки on back drum-type brakes

1 – a rack;
2 – a bolt;
3 – the working brake cylinder;
4 – разжимная a lath with the lever;
5 – a lobby brake колодка;
6 – the lever of a drive of a lay brake;
7 – an antitinkling sound spring;
8 – back brake колодка;
9 – a clip;
10 – the holder;
11 – a brake drum;
12 – a returnable spring;
13 – the bearing;
14 – a washer;
15 – a nut;
16 – a dustproof cap.

Removal

PERFORMANCE ORDER
1. Lift the back party of the car and fix on support.
2. Remove back wheels.
3. Remove a dustproof cap.
4. A small chisel unbend a fillet and turn away a nut.

The prevention

Be careful not to damage a groove and a carving on the axis end.


5. Remove from an axis a brake drum, a washer and bearings as knot in gathering. If it is difficult to remove a brake drum, take away brake колодки.

6. Remove forward and back clips brake колодок and from an underside of a brake board remove racks of support brake колодок.
7. Remove back brake колодки in gathering.
8. Disconnect a cable of a lay brake from back brake колодки.

9. Disconnect a tube from the working brake cylinder.

10. Turn out a bolt of fastening of the working brake cylinder.

11. Remove an antitinkling sound spring.
12. Remove разжимную a lath after removal of a returnable spring.
13. Remove the lever of a drive of a lay brake.

Check

PERFORMANCE ORDER
1. Check up brake drums on absence of cracks, dredging or unequal deterioration.
2. If necessary chisel or replace a brake drum.
3. Measure internal diameter of a brake drum.

4. Replace a brake drum if internal diameter of a drum exceeds maximum permissible value.

The maximum diameter: 201 mm


The prevention

Check up uniformity прилегания brake колодки to a brake drum.


5. Check up overlays brake колодок on absence of pollution by oil or lubricants, deterioration and cracks.
6. Measure a thickness of overlays back brake колодок. Replace all brake колодки on one axis of the car even if only one колодка has a thickness, smaller maximum permissible.

Is minimum admissible thickness: 1,0 mm

Installation

PERFORMANCE ORDER
1. Clear a brake board.
2. With greasing for brakes grease points of contact brake колодок with a brake board and the working brake cylinder.

The prevention

Exclude greasing hit on brake колодки.


3. Establish the working brake cylinder on a brake board.
4. Connect a brake tube to the working brake cylinder.
5. Establish the lever of a drive of a lay brake. Grease interfaced surfaces of a rack and adjust lever position.
6. Connect a cable of a lay brake to the lever of a drive of a lay brake.
7. Establish brake колодки in gathering on the working brake cylinder.
8. From an underside of a brake board establish racks and clips fix on them brake колодки.
9. Establish an adjusting lath in completely released position.

10. Establish a screw-driver against a cam of a regulator and move it to the let out position.

11. Establish a brake drum, a washer and the bearing on an axis.
12. Some times press a pedal of a brake for reduction of the automatic device of adjustment of backlashes brake колодок into position.
13. Screw a new nut. Hammer in a nut fillet into an axis groove.
14. Establish a dustproof cap.