KIA RIO

Since 2000 of release

Repair and car operation



Kia Rio
+ 1.1. Short acquaintance to the car
+ 2. Engines A3E, А5D
+ 3. Greasing system
+ 4. Cooling system
+ 5. Fuel system
+ 6. Ignition system
+ 7. Coupling
+ 8. A transmission
+ 9. Axes and power shafts
+ 10. A suspension bracket
+ 11. Wheels and tyres
+ 12. A steering
- 13. Brake system
   13.1. Specifications
   13.2. Check of the vacuum amplifier of brakes with use of devices
   13.3. The unilateral vacuum valve
   13.4. The vacuum amplifier of brakes
   13.5. Prorolling of hydraulic system of a drive of brakes
   13.6. Check of brake tubes
   13.7. Check and replacement of brake hoses
   + 13.8. A brake pedal
   13.9. Replacement of lobbies brake колодок
   13.10. Replacement brake колодок on back drum-type brakes
   13.11. Repair of a support of a forward brake
   13.12. Repair of the working brake cylinder
   13.13. The main brake cylinder
   13.14. The pressure terminator
   13.15. A lay brake
   13.16. The block of management ABS
   13.17. The block of hydraulic management (HCU)
   13.18. The forward gauge of frequency of rotation of a wheel
   13.19. The back gauge of frequency of rotation of a wheel
   + 13.20. A gear rotor of the gauge of frequency of rotation of a wheel
   13.21. The basic survey
   13.22. Check of functionality
+ 14. A body
+ 15. Air central air
+ 16. The electric equipment







13.15. A lay brake
THE GENERAL DATA

Lay brake

1 – the console;
2 – a back part of a cable of a lay brake;
3 – the lever of a lay brake;
4 – an adjusting nut;
5 – a forward part of a cable of a lay brake;
6 – an arm of a cable of a lay brake;
7 – a cover of a cable of a lay brake;
8 – a back part of a cable of a lay brake.

Removal

PERFORMANCE ORDER
1. Turn out a bolt and remove the console of a lay brake.
2. Disconnect an electric socket from the switch of a lay brake.

3. Loosen the an adjusting nut of a cable of a lay brake.
4. Turn out two nuts and a bolt and remove the lever of a lay brake.
5. Disconnect a forward part of a cable of a lay brake from back parts of a cable of a lay brake.
6. Remove an arm of a back cable of a lay brake.
7. Turn out two bolts of fastening of hinges of a back seat.
8. Remove a back seat.
9. Remove furnish of a threshold of a back door.
10. Release clamps of a carpet covering and turn away it for access to a cover of a cable of a lay brake.
11. Turn away a nut of fastening of a cover of a cable of a lay brake.
12. Uncover a cable of a lay brake.
13. Lift the car and fix on support.
14. Remove back wheels.
15. Remove a back brake drum and brake колодки in gathering.
16. Disconnect a cable of a lay brake from the lever on brake колодке.
17. Turn away a nut and a bolt of fastening of a cable of a lay brake.
18. Extend a cable of a lay brake through an aperture in a body and remove it from the car.

19. Extend a cable of a lay brake through an aperture in a brake board.

Installation

PERFORMANCE ORDER
1. Insert a cable of a lay brake through an aperture in a body.
2. Insert a cable of a lay brake through an aperture in a brake board.
3. Fix a cable of a lay brake on the lever back brake колодки.
4. Establish a back brake drum.
5. Fix a cable of a lay brake nuts and a bolt.

The inhaling moment: 19–26 Nm

6. Establish a wheel.
7. Lower the car.
8. Establish a cover of a cable of a lay brake.

The inhaling moment: 19–26 Nm

9. Establish an arm of fastening of a back part of a cable of a lay brake.

The inhaling moment: 19–26 Nm

10. Establish into place a carpet covering and furnish of a threshold of a back door.
11. Establish a back seat.

The inhaling moment: 19–26 Nm

12. Connect forward and back parts of a cable of a lay brake and fix their clamp.
13. Establish the lever of a lay brake.

The inhaling moment: 19–26 Nm

14. Pass a cable through the lever of a lay brake and screw an adjusting nut.
15. Establish the switch of a lay brake.
16. Establish the console of a lay brake.

The prevention

Check up quantity of clicks at a tightening of the lever of a lay brake. Be convinced that at a lever tightening on one click the control lamp of a lay brake lights up.


Adjustment

PERFORMANCE ORDER
1. Check up that the lever of a lay brake is in completely released position.
2. Lift a back part of the car so that back wheels could rotate freely.
3. Rotating an adjusting nut, adjust a lay brake so that at a tightening of the lever effort of 10 kg it rose on 5–7 clicks.

The prevention

Back wheels should затормаживаться at a tightening of the lever of a lay brake on 5–7 clicks.


4. Do not bend a cable of a lay brake at an angle 90 and more.
5. Check up work of a lay brake.