KIA RIO

Since 2000 of release

Repair and car operation



Kia Rio
+ 1.1. Short acquaintance to the car
+ 2. Engines A3E, А5D
+ 3. Greasing system
+ 4. Cooling system
+ 5. Fuel system
+ 6. Ignition system
+ 7. Coupling
+ 8. A transmission
+ 9. Axes and power shafts
+ 10. A suspension bracket
+ 11. Wheels and tyres
+ 12. A steering
+ 13. Brake system
+ 14. A body
+ 15. Air central air
- 16. The electric equipment
   16.1. Specifications
   16.2. Electric chains
   + 16.3. The generator
   + 16.4. The storage battery
   16.5. A starter
   16.6. Check at проворачивании a cranked shaft not the heated-up engine
   16.7. Check of an electric chain of the traction relay
   16.8. Check of the traction relay
   16.9. Check of brushes and щеткодержателя
   16.10. Check of coils статора
   16.11. Rotor check
   16.12. Removal and starter installation
   16.13. Starter repair
   16.14. The multipurpose switch
   16.15. A sound signal
   16.16. The block of safety locks and the relay, established in car salon
   16.17. Check of the relay of the activator of the lock of a door
   16.18. Check of the switch of adjustment of position of an external rear-view mirror
   16.19. Check of the activator of position of an external rear-view mirror
   16.20. Engine check стеклоподъемника
   16.21. Check of a heater of back glass
   16.22. Repair of a current-carrying strip of a heater
   16.23. The engine of a screen wiper of a windscreen
   16.24. Стеклоомыватели
   16.25. Adjustment of light of headlights
   16.26. Adjustment of light of antifog headlights
   16.27. Safety pillows (SRS)
   16.28. Precautionary labels
   16.29. A pillow of safety of the driver and a spiral wire
   16.30. Check of a pillow of safety
   16.31. Check of a spiral wire (spring)
   16.32. A pillow of safety of the forward passenger
   + 16.33. Electric schemes







16.23. The engine of a screen wiper of a windscreen
THE GENERAL DATA

Screen wipers of wind and back glasses

1 – a cowl lattice;
2 – the lever of a screen wiper of a windscreen;
3 – the engine of a screen wiper of a windscreen;
4 – draughts of a screen wiper of a windscreen;
5 – the lever of a screen wiper of back glass;
6 – the engine of a screen wiper of back glass.

Check of frequency of work of a screen wiper

PERFORMANCE ORDER
1. Disconnect a socket from the screen wiper engine.
2. Additional wires connect the positive plug of the storage battery to contact 4 sockets, and the negative plug – to contact 1.
3. Be convinced that the screen wiper engine works on low frequency of rotation.
4. Additional wires connect the positive plug of the storage battery to contact 4 sockets, and the negative plug – to contact 2.
5. Be convinced that the screen wiper engine works on high frequency of rotation.

Check of an automatic stop of brushes in an initial condition

PERFORMANCE ORDER
1. Include the engine on low frequency of rotation.
2. Having disconnected a wire from contact of 1 socket, stop the engine in any position, except the initial.
3. Connect contacts 1 and 5 sockets.
4. Additional wires connect the positive plug of the storage battery to contact 4 sockets, and the negative plug – to contact 3.
5. Check up that the screen wiper engine is switched off in a starting position of brushes of a screen wiper.

Adjustment

PERFORMANCE ORDER
1. Establish screen wiper levers on an axis in a starting position.
2. Screw nuts of fastening of levers and tighten their demanded moment.

The inhaling moment: 18–22 Nm

3. Establish covers on nuts and check up work of a screen wiper of a windscreen. Screen wiper brushes should stop in a starting position on distance of 41 mm from outside the forward passenger and – 40 mm from outside the driver.