KIA RIO

Since 2000 of release

Repair and car operation



Kia Rio
+ 1.1. Short acquaintance to the car
+ 2. Engines A3E, А5D
+ 3. Greasing system
+ 4. Cooling system
+ 5. Fuel system
+ 6. Ignition system
+ 7. Coupling
+ 8. A transmission
+ 9. Axes and power shafts
+ 10. A suspension bracket
+ 11. Wheels and tyres
+ 12. A steering
+ 13. Brake system
+ 14. A body
+ 15. Air central air
- 16. The electric equipment
   16.1. Specifications
   16.2. Electric chains
   + 16.3. The generator
   - 16.4. The storage battery
      16.4.1. Normal gymnastics of the storage battery
      16.4.2. The accelerated gymnastics of the storage battery
      16.4.3. Check of the storage battery
      16.4.4. Check of level of electrolit
      16.4.5. Check of density of electrolit
      16.4.6. Check of pressure of the storage battery
      16.4.7. Check of pressure of the storage battery under loading
      16.4.8. Check of the current consumed from the storage battery at switched off ignition
      16.4.9. Power failure check on connections of plugs of the storage battery
   16.5. A starter
   16.6. Check at проворачивании a cranked shaft not the heated-up engine
   16.7. Check of an electric chain of the traction relay
   16.8. Check of the traction relay
   16.9. Check of brushes and щеткодержателя
   16.10. Check of coils статора
   16.11. Rotor check
   16.12. Removal and starter installation
   16.13. Starter repair
   16.14. The multipurpose switch
   16.15. A sound signal
   16.16. The block of safety locks and the relay, established in car salon
   16.17. Check of the relay of the activator of the lock of a door
   16.18. Check of the switch of adjustment of position of an external rear-view mirror
   16.19. Check of the activator of position of an external rear-view mirror
   16.20. Engine check стеклоподъемника
   16.21. Check of a heater of back glass
   16.22. Repair of a current-carrying strip of a heater
   16.23. The engine of a screen wiper of a windscreen
   16.24. Стеклоомыватели
   16.25. Adjustment of light of headlights
   16.26. Adjustment of light of antifog headlights
   16.27. Safety pillows (SRS)
   16.28. Precautionary labels
   16.29. A pillow of safety of the driver and a spiral wire
   16.30. Check of a pillow of safety
   16.31. Check of a spiral wire (spring)
   16.32. A pillow of safety of the forward passenger
   + 16.33. Electric schemes







16.4.9. Power failure check on connections of plugs of the storage battery
THE GENERAL DATA

Power failure check on connections of plugs of the storage battery will allow to define resistance size between a wire connected to the plug of the storage battery and the plug of the storage battery.

At performance of this check it is necessary to remember that the power failure between two points of connection to which are connected щупы the voltmeter, testifies to resistance presence in connection.

PERFORMANCE ORDER
1. Connect "positive" щуп the voltmeter to a wire connected to the negative plug of the storage battery.
2. Connect "negative" щуп the voltmeter to the negative plug of the storage battery.
3. Include ignition and observe of voltmeter indications. If the voltmeter shows pressure presence, means, there is no reliable contact between a wire and the plug of the storage battery.
4. Connect "positive" щуп the voltmeter to a wire connected to the positive plug of the storage battery.
5. Connect "negative" щуп the voltmeter to the positive plug of the storage battery.
6. Include ignition and observe of voltmeter indications. If the voltmeter shows pressure presence, means, there is no reliable contact between a wire and the plug of the storage battery.
7. Connect the voltmeter for power failure measurement between the positive plug of the storage battery and contact of the traction relay to which the wire from the storage battery is connected.
8. Include ignition and a starter and observe of voltmeter indications. If pressure exceeds 0,2 In, it is necessary to clear and draw in contacts of a socket and to repeat check. If pressure still exceeds 0,2 In, it is necessary to replace a wire connecting the positive plug of the storage battery and the traction relay of a starter.
9. Connect the voltmeter for power failure measurement between the negative plug of the storage battery and the block of cylinders of the engine.
10. Include ignition and a starter and observe of voltmeter indications. If pressure exceeds 0,2 In, it is necessary to clear and reliably to tighten wire fastening to the block of cylinders. If pressure still exceeds 0,2 In, it is necessary to replace a wire connecting the negative plug of the storage battery and the block of cylinders of the engine.
11. Connect "positive" щуп the voltmeter to the starter case. Connect "negative" щуп the voltmeter to the negative plug of the storage battery.
12. Include ignition and a starter and observe of voltmeter indications. If pressure exceeds 0,2 In, the starter means is unreliably fixed on the block of cylinders of the engine.