KIA RIO

Since 2000 of release

Repair and car operation



Kia Rio
+ 1.1. Short acquaintance to the car
+ 2. Engines A3E, А5D
+ 3. Greasing system
+ 4. Cooling system
+ 5. Fuel system
+ 6. Ignition system
+ 7. Coupling
- 8. A transmission
   + 8.1. A mechanical transmission
   - 8.2. Automatic transmission F4E–K
      8.2.1. Specifications
      8.2.2. Check of work and adjustment of position of the lever of the selector
      8.2.3. Testing of teamwork of an automatic transmission and the engine for the motionless car (stall test)
      8.2.4. Time lag testing (Lag test)
      8.2.5. Pressure check трансмиссионной liquids
      8.2.6. Check of level and liquid replacement in an automatic transmission
      8.2.7. Procedure of replacement of a liquid in the converter of an automatic transmission
      8.2.8. Leaks of a liquid from an automatic transmission
      8.2.9. Replacement of oil sealing rings
      8.2.10. Removal and installation of an automatic transmission
      8.2.11. Repair of an automatic transmission
      8.2.12. A radiator of cooling of a liquid of an automatic transmission
      8.2.13. The block of valves
      8.2.14. The case of regulating valves
      8.2.15. The oil pump
      8.2.16. Check of resistance of the gauge of frequency of rotation of an entrance shaft \of a turbine wheel
      8.2.17. Check of resistance of the gauge of speed
      8.2.18. The switch of operating modes of transmission O\D
      8.2.19. The switch of a range of a transmission
      8.2.20. The gauge of temperature of an automatic transmission
      8.2.21. Electromagnetic valves
      8.2.22. The linear electromagnetic valve
      8.2.23. The selector lever
      8.2.24. Repair of the lever of the selector
      8.2.25. Check of functioning of the mechanism of blocking of the lever of the selector
+ 9. Axes and power shafts
+ 10. A suspension bracket
+ 11. Wheels and tyres
+ 12. A steering
+ 13. Brake system
+ 14. A body
+ 15. Air central air
+ 16. The electric equipment







8.2.12. A radiator of cooling of a liquid of an automatic transmission
THE GENERAL DATA

Radiator of cooling of a liquid of an automatic transmission

1 – a target tube of a liquid of an automatic transmission (hotter hose);
2 – a connecting bolt;
3 – a washer;
4 – a target hose of a liquid of an automatic transmission (hotter hose);
5 – an entrance tube of a liquid of an automatic transmission (colder hose);
6 – a radiator;
7 – a connecting bolt;
8 – a washer.

Removal

PERFORMANCE ORDER
1. Lift the car and fix on support.
2. Turn out seven screws and remove the right mudguard of a motor compartment.
3. Establish under a radiator the pallet for liquid gathering.
4. Disconnect entrance and target hoses of a liquid of an automatic transmission.
5. Remove entrance and target tubes of a liquid of an automatic transmission.
6. Remove a radiator.

Installation

PERFORMANCE ORDER
1. Establish a radiator.
2. Establish entrance and target tubes of a liquid of an automatic transmission.

The inhaling moment: 32–47 Н

3. Pull entrance and target hoses over tubes of a liquid of an automatic transmission so that end faces of hoses have reached fillets on tubes.
4. Establish a hose clip on a hose in the centre of marks and under the corner shown in drawing.
5. Check up that the hose clip does not concern any other parts.
6. Establish the right mudguard of a motor compartment and fix seven screws.
7. Lower the car.
8. Check up liquid level in an automatic transmission.