KIA RIO

Since 2000 of release

Repair and car operation



Kia Rio
+ 1.1. Short acquaintance to the car
+ 2. Engines A3E, А5D
+ 3. Greasing system
+ 4. Cooling system
+ 5. Fuel system
+ 6. Ignition system
+ 7. Coupling
- 8. A transmission
   + 8.1. A mechanical transmission
   - 8.2. Automatic transmission F4E–K
      8.2.1. Specifications
      8.2.2. Check of work and adjustment of position of the lever of the selector
      8.2.3. Testing of teamwork of an automatic transmission and the engine for the motionless car (stall test)
      8.2.4. Time lag testing (Lag test)
      8.2.5. Pressure check трансмиссионной liquids
      8.2.6. Check of level and liquid replacement in an automatic transmission
      8.2.7. Procedure of replacement of a liquid in the converter of an automatic transmission
      8.2.8. Leaks of a liquid from an automatic transmission
      8.2.9. Replacement of oil sealing rings
      8.2.10. Removal and installation of an automatic transmission
      8.2.11. Repair of an automatic transmission
      8.2.12. A radiator of cooling of a liquid of an automatic transmission
      8.2.13. The block of valves
      8.2.14. The case of regulating valves
      8.2.15. The oil pump
      8.2.16. Check of resistance of the gauge of frequency of rotation of an entrance shaft \of a turbine wheel
      8.2.17. Check of resistance of the gauge of speed
      8.2.18. The switch of operating modes of transmission O\D
      8.2.19. The switch of a range of a transmission
      8.2.20. The gauge of temperature of an automatic transmission
      8.2.21. Electromagnetic valves
      8.2.22. The linear electromagnetic valve
      8.2.23. The selector lever
      8.2.24. Repair of the lever of the selector
      8.2.25. Check of functioning of the mechanism of blocking of the lever of the selector
+ 9. Axes and power shafts
+ 10. A suspension bracket
+ 11. Wheels and tyres
+ 12. A steering
+ 13. Brake system
+ 14. A body
+ 15. Air central air
+ 16. The electric equipment







8.2.14. The case of regulating valves
THE GENERAL DATA

The case of regulating valves

1 – the block of the mesh filter;
2 – a sealing ring to (replace);
3 – маслопровод;
4 – a sealing ring of round section to (replace);
5 – the switching solenoid And (1–2 solenoid);
6 – the solenoid of coupling of the converter of a twisting moment;
7 – mesh filters;
8 – rubber balls;
9 – the preliminary case of regulating valves;

10 – lining Е to (replace);
11 – the bottom plate of a separator;
12 – the oil filter;
13 – lining F to (replace);
14 – the mesh filter;
15 – the bottom case of regulating valves;
16 – a steel ball.

 

The case of regulating valves

1 – the linear electromagnetic valve;
2 – switching solenoids B and C;
3 – the top case of regulating valves;
4 – a lining to (replace);
5 – screws;
6 – the top plate of a separator;
7 – the oil filter;
8 – a lining In to (replace);
9 – the main case of regulating valves;
10 – a lining With to (replace);
11 – screws;
12 – the main plate of a separator;
13 – lining D to (replace);
14 – rubber balls;
15 – the mesh filter.

Removal


The prevention

At work with the case of regulating valves be especially cautious as it consists a considerable quantity of exact details.

At removal have details in a certain order not to mix them.

Clear the removed details solvent and dry up their compressed air. Clean all apertures and channels the compressed air.


PERFORMANCE ORDER
1. Turn out bolts and remove маслопровод.
2. Remove sealing rings with маслопровода.
3. Remove switching solenoid A.
4. Remove the solenoid of coupling of the converter of a twisting moment and the mesh filter.
5. Remove switching solenoids B and C and mesh filters.
6. Remove the linear electromagnetic valve.
7. Turn out nine bolts of fastening of the top case of regulating valves.
8. Turn out two screws from the top case of regulating valves.
9. Remove lining B, the top plate of a separator, the oil filter, the mesh filter and lining A.

10. Turn out seven bolts and remove the main regulating valve.
11. Remove lining D, the main plate of a separator and lining C.
12. Remove four rubber balls from the main case of the regulating valve.
13. Remove the oil mesh filter, steel and two rubber balls from the additional main case of regulating valves.
14. Turn out six bolts and remove the additional main case of regulating valves.
15. Remove lining E, the bottom plate of a separator, the oil filter and lining F.
16. Remove the oil mesh filter from the bottom case of regulating valves.

Arrangement of mesh and oil filters on the bottom case of regulating valves

Arrangement of the oil filter on the bottom party of the additional main case of regulating valves

Arrangement of steel and rubber balls and the mesh filter in the additional main case of regulating valves

Arrangement of rubber balls in the main case of regulating valves

Arrangement of the oil filter on the top party of the case of regulating valves

Arrangement of mesh and oil filters on the top case of regulating valves

Installation sites and length of bolts of fastening of details of regulating valves

Installation

PERFORMANCE ORDER
1. Establish the oil mesh filter in the bottom case of regulating valves.
2. Establish the oil filter in the bottom plate of a separator.

The prevention

Lining F and lining E are not interchangeable. They are identified by the form in the area shown in drawing.


3. Establish lining F on a plate of a separator and new lining E on the bottom case of valves.
4. Establish the additional main case of regulating valves on the bottom case and fix seven bolts.

The inhaling moment: 7,9–10,7 Nm

5. Establish two rubber balls and oil mesh filters in the additional main case of regulating valves.
6. Establish rubber balls in the main case of regulating valves.
7. Establish new lining C, a plate of a separator and lining D on the main case of regulating valves

The prevention

Lining With and lining D are not interchangeable.


8. Fix lining C, a plate of a separator and lining D to the main case two bolts.

The inhaling moment: 1,27–1,86 Nm

9. Establish the main case of regulating valves on the additional main case of regulating valves.


The prevention

Arrange heads of bolts as is shown in drawing.


10. Freely screw bolts.
11. Establish the oil filter in the top plate of a separator.

The prevention

Lining And and a lining In are not interchangeable. They are identified by the form in the area shown in drawing.


12. Establish new lining A, the top plate of a separator and new lining B on the top case of regulating valves.
13. Two bolts fix to the main case of the regulating valve lining A, the top plate of a separator and lining B.
14. Establish the top case of regulating valves on the main case of regulating valves and fix nine bolts.

The inhaling moment: 7,9–10,7 Nm

15. Freely screw bolts of fastening of the bottom case of regulating valves.
16. Establish the linear electromagnetic valve.

The inhaling moment: 7,9–10,7 Nm

17. Establish solenoids B and C, oil mesh filters and an arm.
18. Tighten bolts the demanded moment.

The inhaling moment: 7,9–10,7 Nm

19. Establish coupling of the converter of a twisting moment and the oil mesh filter.

The inhaling moment: 7,9–10,7 Nm